Operating and InstallationInstructionsGas CombisetCS 1012To prevent accidents andmachine damage,read the Operating Manualbeforeinstallation or use.M.-
Burnern Burner capo Burner headp Thermocoupleq Ignitorr Burner baseGuide to the combiset10
Cleaning the combisetBefore using for the first time clean theappliance as follows:^Remove any protective foil.^Wash the removable parts of the gasbur
Fast-Ignition-SystemThe gas combisets are equipped with aFast-Ignition-System whichincorporates the following features:–The control knob does not need
Turning on^To turn on the burner, press thecontrol knob down to pass theresistance, then release the pressureand turn it counterclockwise to thelarges
Pan size–Set the combiset to a high flamewhen using a large diameter pan andlow flame when using a smalldiameter pan.–Generally, wide / shallow pans w
Ignition safety controlThis appliance is equipped with anIgnition Safety Control. This control cutsthe gas supply if the flame goes outand reignition
Never use a steam cleaner to cleanthis combiset. Pressurized steamcould cause permanent damage tothe surface and to components forwhich the manufactur
BurnersThe burner can be dismantled andcleaned when cool.^Remove the burner parts and washthem in a solution of warm water andliquid dish soap. Dry th
,Repairs should only be carries out by an authorized technician inaccordance with local and national safety regulations. Unauthorized repairscould cau
The burner does not ignite after several attempts.Possible fault SolutionDisconnect the appliance from the electrical supply for a few seconds. If the
2WARNING:If the information in this manual is not followedexactly, a fire or explosion may result causingproperty damage, personal injury or death.–Do
The igniter does not spark.Possible fault SolutionThe circuit breaker has tripped. Re-set the circuit breaker. Contact anelectrician for assistance if
In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this bo
Installation InstructionsIMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USETo prevent accidentsand machine damageread these instructionsbef
InstallationThe minimum distances given inthese Installation instructions are tocombustible surfaces, and must beobserved to ensure safe operation.Fai
Safety distances above theapplianceThe minimum safety distance given bythe hood manufacturer must bemaintained between the combiset andthe hood above
Safety distances to the sidesof the applianceThe appliance should only be installedas shown in the illustrations, whilemaintaining the required safety
Safety distance when installing the appliance near a wall with trim or a backsplashA minimum distance of 2" (50 mm) between the trim or back spla
Installation dimensionsa Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e Gas fitti
Cut out^Make the countertop cut-out for thedesired number of appliances.Remember to maintain a minimumsafety distance from the back wall,as well as fr
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Guide to the combiset . . . . . . . . . . . . . . . .
Installation of multipleappliancesWhen installing more than one combiset appliance, a support bar b must beinstalled between the appliances.Countertop
Sample calculations for a countertop cut-out for three appliancesAappliance widthminus 5/16"(8 mm)Bappliance widthCappliance widthminus 5/16"
a Spring clipsb Support barsc Space between support bar and countertopAn additional support bar is required for each additional appliance. The positio
Attach the spring clips andsupport barsWood or solid surface countertops^Place the supplied spring clips aand the support bars b at themarked position
^Coat the edges of the spring clips,^and the space d between the stripsand the countertop with silicone(supplied).Installation34bda
Installing the appliance^Feed the power cord down throughthe cut-out.^Then place the front side of theappliance in the countertop cut-out.^Then with a
SealingThe appliance must not be permanentlysealed into the countertop wheninstalled. The sealing strip under theedge of the appliance provides asuffi
This appliance must be groundedaccording to local or national codes.All electrical work should beperformed by a qualified electricianin accordance wit
Wiring DiagramElectrical connection38
Installation and service must beperformed by a qualified installer,service agency or the gas supplier.In Massachusetts a licensedplumber/gas fitter is
WARNING- When using your gasappliance follow basicprecautions, including thefollowing:This gas combiset conforms to alluniform safety codes andregulat
Gas pressure regulatorA pressure regulator that is convertiblefrom natural to LP gas (Propane) or viceversa is included with the appliance.The include
Nominal ratingsMaximum outputGas type BTU/hr kWNormal burner Natural Gas (NG)Propane (LP)5,7005,0001.651.45Fast burner Natural Gas (NG)Propane (LP)10,
The combiset should have beenordered for connection to either naturalgas or LP gas (propane).If the combiset is not configured for theproper type of g
Disposal of packing materialsThe cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle.Ensure that any plastic wrappings,
Alteration rights reserved / 2508For the most updated manual see the Miele web site.M.-Nr. 07 366 180 / 00
Technical safety~Installation, repair and maintenancework should be performed by a Mieleauthorized service technician. Work byunqualified persons coul
~Before servicing, turn off the gasvalve and disconnect the power supplyby either removing the fuse, unpluggingthe unit or manually “tripping” thecirc
~Do not use pans that extend pastthe burner grate. Using larger pansmay cause the flames to spread outand damage the surroundingcountertop or other co
~Make certain that the power cords ofsmall appliances do not come incontact with the appliance. Theinsulation of the cable could becomedamaged. Danger
a Fast burnerb Normal burnerc Burner grated Burner indicatorse Display panelIndicatorsl On/Off indicatorm "Residual Heat" IndicatorControl k
Comments to this Manuals