Miele T 9822 User Manual

Installation InstructionsT 9822 Gas DryerTo prevent accidentsand appliance damageread these instructionsbeforeinstallation or use.M.-Nr. 07 431 110en

Confined space installation^When installed in any space with lessthan 122 square feet (11.3 m2),minimum clearances around thedryer must be adhered to

Transporting the dryer to theinstallation siteThe rear of the lid has a handle fortransportation.^Use the front dryer feet and the rearof the lid to m

,WARNINGBefore installation, disconnect thetumble dryer from the electricalsupply by shutting off the powermain or tripping the circuit breaker.Be sur

,GROUNDING INSTRUCTIONSThis appliance must be grounded.In the event of malfunction orbreakdown, grounding will reducethe risk of electric shock byprov

,WARNINGInstallation and service must beperformed by a qualified installer,service agency or gas supplier.In Massachusetts a licensedplumber / gas fit

Gas supplyInstallation material (hoses andadapters) must be provided by theinstaller.Gas connection distancesThis appliance must be installed with its

,To secure all connections useappropriate Teflon tape or a threadcompound, suitable for gasconnections.^ At the end of the dryer's gasconnection

^Using two wrenches tighten theflexible gas line connection.^Connect the flare union adapter, a,to the pressure tapping plug, b,originally installed o

Exhaust ducting andconnectionsA gap of3/8" (10 mm) must beprovided between the applianceand the floor. This gap is necessaryfor proper air flow a

How to calculate the effectiveduct lengthThe overall duct length will determinethe duct diameter (see the "Additionalduct lengths" table). I

2

Tips about the ductwork–Check with your local building codeto determine the maximum allowableduct length.–Only use rigid or flexible metal ductfor exh

Additional duct lengths (4" [100 mm] rigid pipe only)Type of bend Radius Additional duct lengthinches cm ft cmFlexible metal duct–3’ 3" (1 m

ExampleRigid pipe Duct lengthftDuct lengthmAWall duct with louveredwall vent12’ 5" 3.8 mB90° bend2’ 4" 0.7 mC20" (0.5 m) rigid pipe1’ 7

Exhaust connection with aflexible exhaust hose or rigidpipeUsing the adapter supplied, anexhaust hose (4" [100 mm]diameter) can be installed.Nece

^Install the exhaust hose 3 in the dryerusing the adapter 2 and therestriction insert 3.If using the gray adapter without clips :^Plug the restriction

Direct wall connectionNecessary materials:–a wall pipe–flexible foam gasketDryer top view1 Wall pipe2 Flexible foam gasketDryer side view1 Wall pipe2

Disposal of the packingmaterialsThe packing materials protect theappliance during shipping. They havebeen designed to be biodegradableand recyclable.T

27

Alteration rights reserved / 1612INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOSTCURRENT PRODUCT SPECIFICATIONS, TECHN

3,WARNINGFor your safety the information in this manualmust be followed to minimize the risk of fire orexplosion or to prevent property damage,persona

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Installation . . . . . . . . . . . . . . . . . . . . .

Installation and connection, WARNING - Risk of FireWhen using your gas appliancefollow basic safety precautionsincluding the following:~It is essentia

~Do not install a clothes dryer withflexible plastic venting materials. Ifflexible metal (foil type) duct isinstalled, it must be of a specific typeid

Front viewa Exhaust connectionb Power cord with plugc Control paneld Doore Four height adjustable screw feetStandA dryer stand, with drawer, can bepur

Reara Handle for transportation (arrows)b Power cord with plugc Slot for moduled Air intakee Gas connectionf Exhaust connection with restrictioninsert

,WARNING:Do not install the dryer:- outdoors- in an environment with drippingwater or weather- near flammable materials- in rooms which may contain ga