Installation instructionsInformation is subject to change. Please refer to our website to obtain the mostcurrent product specification, technical &
The factory setting for the door hingesallows them to open at a wide angle.However, if the opening angle of thedoor needs to be limited for any reason
When reversing the door hinging,always enlist the help of anotherperson.The appliance comes with right-handdoor hinging. If left-hand hinging isrequir
^ Slightly loosen the screws e and fon the hinges.^ Slide the doors g and h outwardsand take them off their hinges.^ Remove the screws e completely.^
Carry out the following steps on bothdoors.Removing the soft-close mechanismCaution! When removed from theappliance, the soft-closemechanism will snap
Attaching the soft-close mechanism^Now turn over the appliance door sothat it lies face down.^ Screw the mount k onto the hingeand firmly tighten.^ Pu
Two people are required to install theappliance.^The appliance must be installed in astable, solid cabinet unit that ispositioned on an even and level
You will need the followinginstallation componentsEach installation component isdesignated by a number. Thecomponent's number can also be foundin
^ Slide the cover strip tabs a intoposition.^Screw the mounting bracket d ontothe pre-drilled holes in the appliancedoor using the hex screw e.Securel
^ Remove the cover f.^ Loosely screw the mounting bracketg onto the top left corner of theappliance using the screws h.Donot tighten the screws; the b
Installing the appliance^Slide the appliance into the cabinetspace until the covers of themounting brackets touch the frontedge of the cabinet side wa
Disposing of packagingmaterialsThe packaging is designed to protectthe appliance from damage duringtransport. The packaging materialsused are selected
Securing the appliance in thecabinet space^ Push the hinged side of theappliance against the cabinet wall.^Screw the particleboard screws sthrough the
^Snap the protruding ends off of themounting brackets. They are nolonger needed and can now bedisposed of.^ Attach the covers f and u to thecorrespond
Mounting the cabinet doors.The cabinet door must have a minimumthickness of 5/8" (16 mm) and amaximum thickness of 3/4" (19 mm).The followin
Carry out the following steps on bothdoors.^ The factory setting for the distancebetween the appliance door and themounting frame is 8 mm. Doublecheck
^Lay the cabinet door face down on astable surface.^ Using a pencil, lightly mark a linedown the centre of the inside of thecabinet door e.^ Hang the
^Open the appliance door.^ Hang the cabinet door onto thealignment bolts h.^ Loosely screw the nuts c onto theadjustment bolts.^Close the door and che
^ Tighten the nuts c on each of theappliance doors using a box-endwrench j while holding thealignment bolts c in place using ascrewdriver.^ The cover
^Tighten all screws again.^ Replace each of the top covers o,and click it into place.^Replace the side covers p, makingsure you hear them click into p
97
98
,Failure to follow theseinstructions can result in death, fire,or electrical shock.Improper connection of theequipment grounding conductormay result i
99,PSRUWHU0LHOH/LPLWHG+HDGTXDUWHUVDQG0LHOH&HQWUH&OUR6ALLEY$RIVE6AUGHAN/.,+6WWWMIELECA&XVWRPHU&DUH&HQWUH0HONE
M.-Nr. 09 969 830 / 01en-CAKFNS 37432 iD
The appliance must be connected to anelectrical outlet that is properlygrounded. The electrical installationmust comply with the applicableelectrical
Safe operation of the appliance isonly assured if it has been installedand connected in accordance withthese operating and installationinstructions.WA
Climate classThe appliance is designed for usewithin a certain climate class (roomtemperature) and should not be usedoutside this range. The climate c
Top ventilation openingThere are different options available forconstructing the top ventilationopening:a Directly above the appliance with avent gril
Before installing the appliance^Before installation, remove theaccessories bag with the installationcomponents and other accessoriesfrom the appliance
Before installation, make sure that the cabinet space matches the requireddimensions. The specified measurements for the ventilation openings must bea
Comments to this Manuals