Installation instructionsfor 60 cm wide fully integrateddishwashersIt is essential to read the operating andinstallation instructions beforeinstalling
Securing piecesTo ensure stability, the dishwasher mustbe fixed securely to the worktop (step5). Two securing pieces are suppliedfor this purpose.^ F
Rear screw feet^ Use a TORX T20 screwdriver to ad-just the rear screw feetto the re-quired height.Higher = turn clockwiseLower = turn anti-clockwiseSe
3.Fitting the matching doorfrontThe front of the dishwasher needs to befitted with a base unit front to match thekitchen furniture. This door front ma
Dimension X must be calculated andnoted before attaching the fixingbracket.Dimension X is the distance shown onthe illustration between the drill hole
There are notches on the fixing bracket,marked a in the illustration.^Lay the fixing bracket on the rear ofthe door front, using dimension X forthe di
Fitting the door frontThe door front is correctly fitted when:– the lower lugs on the fixing bracketrest firmly in the lower slits of thedishwasher ou
4. Adjusting the door frontWhen fitted the door front can be ad-justed up to a maximum of 2 mm up-wards or downwards to match adjoiningunit fronts.^Op
5.Securing the dishwasher^Open the dishwasher door.The holes in the securing piecesmust line up with the long holes inthe worktop cover plate. If this
6.Adjusting the door springsThe door springs are correctly adjustedwhen the door remains stationary whenleft open at 45 °.If the door drops down, then
7.Matching the plinth facia of akitchen runThe plinth area of the dishwasher isnormally covered with a plinth runmatching the kitchen furniture.The he
These installation instructions apply to several different dishwasher models.Model numbers in this booklet refer to the model designation specified on
,Please follow the installation in-structions carefully.All electrical work should be carriedout only by a suitably qualified andcompetent person, in
The wires in the mains lead are col-oured in accordance with the followingcode:Green/yellow = earthBlue = neutralBrown = liveIf the colours of the wir
Connection to the water inlet,Water in the dishwasher mustnot be used as drinking water.–The dishwasher may be connectedto a cold or hot water supply,
Drainage–The machine drainage system is fit-ted with a non-return valve, whichprevents dirty water from flowingback into the machine via the drainhose
You would like to... Then you need... build the dishwasher into a kitchen whichdoes not have a matching plinth run...a separate plinth kitavailable
Dishwasher model G 643 G 843Height 81.7 cm(adjustable + 5.0 cm)83.7 cm(adjustable + 5.0 cm)Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0
Dishwasher model G 653 - G 663 G 853 - G 863Height 81.7 cm(adjustable + 5.0 cm)83.7 cm(adjustable + 5.0 cm)Height of building in recess 82 cm (+ 5.0 c
Alteration rights reserved (NovoPlus Vi60) / 1003This paper consists of cellulose which has been bleached without the use of chlorine.M.-Nr. 05 585 95
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Opening the door. . . . .
This dishwasher is specially designedfor integration under a worktop run in afitted kitchen.–The front of the dishwasher is de-signed to take a front
Building in dimensionsDishwasher models G 643 - G 6631) Machine height 870 mm2) Machine height 820 mmAdjustment range approx. 5 cm(82 -87 cm total hei
1.Fitting protective cover plateto worktopThe plexiglass relfector panel and allother installation items required areincluded in the accessories packs
^Align the cover plate to the frontedge of the worktop in the middle ofthe niche.If the worktop has a very roundededge, pull the cover plate further f
Granite or marble worktops:Worktops made from hard materialssuch as granite or marble do not needthe cover plate for protection. Thecover plate is onl
2.Building the dishwasherinto a nicheConnection to water and drainageshould be sited beside and not behindthe dishwasher for accessibility.Connections
I want the document