Miele 36160301USA Installation Manual

Operating and Installation InstructionsWine Storage UnitTo prevent accidents and appliance damage read these instructionsbefore installation or use.M.

Using the settingsThis appliance is operated with the useof touch keys activated by a finger.– An available button will appear white.– A selected butt

^ To de-select a temperature zonetouch the sensor button for thatparticular zone so that it turns white,or select another sensor button.^ To leave the

Turning the button soundOn/OffIf you prefer the buttons to be silentwhen touched, the button sound can beturned off.^ Touch the access button "p&

Turning off for longer periodsof timeIf the appliance is not going to be usedfor an extended time (for example,during a vacation) some precautionsshou

The appliance is equipped with analarm system, to ensure that thetemperature does not rise unnoticedbecause of energy loss or an opendoor.The alarm sy

Wine will continue to mature dependingon the surrounding conditions. Thelength of time which wine can be keptin good condition will therefore dependno

Temperatures can be independentlyset in all three zones.The unit comes factory pre-set for whitewine, red wine, and wine storage.The temperatures can

Insulation panels for thermalseparationThe unit has two fixed insulation panels,to divide the interior into the threedifferent temperature zones. This

Temperature unit(Fahrenheit/Celsius)The temperature can be displayed indegrees Fahrenheit (°F) or Celsius (°C).^ Touch the access button "p"

HumidityIn a conventional refrigerator, thehumidity levels are too low for storingwines. High humidity levels (60 - 70 %)are very important for the st

IMPORTANT SAFETY INSTRUCTIONS...4Guide to the wine storage unit ...7Before use ...

^ While holding down the X button,press the access button "p" once.Keep holding the X button down untilthe following appears in the display(

Storage tips– Always unpack bottles – do not storewine in crates or boxes.– Always lay bottles on their side forstorage. This keeps the corks moistfro

Bottle display rackThe display rack, allows you to displayselected bottles so they can be seeneven with the door closed.^ Lay the wine bottles in the

Display lightingThe display lighting can be turned on ifyou wish the bottles to be lit up evenwhen the door is closed.Turning on^ Touch the access but

During normal operation, condensateand frost can form on the rear wall ofthe refrigerator and drawers.You do not need to remove thisbuild-up, it will

To reduce the risk of electricalshock, disconnect the appliancefrom the power supply by shuttingoff the power main, tripping thecircuit breaker or unp

Before cleaning^ Use the main switch to turn theappliance off completely.The main switch is located on the rightside underneath the control panel.^ Un

Changing the light bulbsDo not remove the light covers forthe display lighting. Should thelighting covers be damaged or needto be removed due to damag

With the aid of the following guide minor problems can be corrected without a ser-vice call.Repairs should only be carried out by a qualified and trai

What if the alarm is ringing?Possible fault SolutionThe appliance door has been open forlonger than 5 minutes.Close the door.What if the alarm is ring

Furniture/fixtures ...36Custom door panels ...37Installatio

Normal noises What causes themBrrrrr... This noise may get louder for brief periods when the motorkicks on.Blub, blub... A gurgling noise can be hear

In the event of a fault which you cannotcorrect yourself, please contact– your Miele dealeror– Miele Technical Service.See back cover of the this manu

32

Installation InstructionsInformation is subject to change. Please refer to our website to obtain the mostcurrent product specification, technical &

Disposing of the packagingmaterialsThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are

,In areas with a tropical climate(over 100°F/38°C and more than70% air humidity) the wine coolermust only be operated in airconditioned locations. Oth

Installation siteThe appliance should be installed in adry, well ventilated room.Do not install the appliance:- outdoors,- in an environment with drip

Installation nicheTo ensure safe, trouble-free installationand the best possible cosmetic result,check to be sure that the installationspace complies

Installation optionsThere are many different installationoptions. You are limited only by thedesign of the kitchen.The door hinge cannot beexchanged.S

Installation with partition using the"Merging Kit"The minimum thickness of the partitionis5/8" (16 mm).If there is a partition with a t

When using the appliance, followbasic safety precautions, includingthe following:Read all instructions beforeinstallation and use to preventaccidents

Side panelsIf one side of the appliance is visible, aside panel must be used.The side panel must be firmly securedto the wall, the floor and the overh

Door dimensions (open min. 90°)KWT 1603 Vi, KWT 1613 Vi*The dimensions of the doorfronts and handles will varyaccording to each individualkitchen.Door

Niche dimensionsKWT 1603 Vi, KWT 1613 ViDimensions42E*: The position of the electrical connection should not be higher than 9" from the floor.Ple

Door front dimensionsDimensions43

Before you beginRead these instructions completelyand carefully.Have the appliance installed by aqualified technician, according tothe enclosed instal

Aligning the housing unitThe housing unit must be carefullyaligned using a spirit level beforeinstalling the appliance. The unitcorners must be at rig

^ Do not remove the installationsupports from the appliance doors.They will be used later in theinstallation niche.There are transportation safetydevi

Preparing the installationniche,Keep the appliance door closeduntil it is securely fastened in theniche. Tipping hazard.Because of the size and weight

Two anti-tip brackets arerecommended for each appliance. Forside-by-side installations 4 brackets arerecommended.Two anti-tip bracketsare recommended

– The beam must cover the applianceby at least 2" (50.8 mm).^ Mark the installation height (loweredge of the beam) on the rear wall ofthe niche.^

InstallationThis appliance is top-heavy andmust be secured to prevent thepossibility of tipping forward.Keep the door closed until theappliance is com

^ Plug the appliance into the poweroutlet a.The plug of the appliance should beeasily accessible after installation.If the plug is not accessible afte

Important!When unscrewing theheight-adjustable feet, proceedgradually, alternating between leftand right.^ Unscrew the height-adjustable feetuntil the

^ Secure the attachment plate side lugs.If there is a fairly large gap above theappliance, cut a wooden beam to fitexactly and place it in the gap.^ I

^ Open the appliance door.^ Screw the attachment plate lugs k tothe adjacent furniture/fixtures.With side-by-side combinations, onlythe external side

^ Measure the distance X between thebracket and the overheadfurniture/fixtures.^ Loosen the two nuts.Set aside the nuts - you will needthem again late

The bracket includes a variety of holesfor the various design options ofcustom doors.When performing any work on thecustom door, always observe thefol

Attaching and aligning thecustom door front^ Insert the angle trim m as far as it willgo in the spaces provided in themounting frame.^ Open the door a

Attaching the covers^ To mount the cover strips on bothsides of the door, click them intoplace from bottom to top, into thegap between the appliance d

Attaching the toe-kick coverThe maximum height of the toe-kickcover is 4" (102 mm) from the top ofthe floor. Do not cover ventilationslits in the

^ Cut the cover strips (long for thesides of the door) to the requiredlength X.^ Push the cover strips on the into thegap between the furniture door a

~Never use a steam cleaner to cleanthe appliance. Pressurized steam coulddamage electrical components andcause a short circuit.~Do not use any electri

^ Position the air separator in thecenter of the appliance door.^ From below, screw the air separatorfirmly onto the door with the 2screws.Installatio

,Avoid the risk of electricalshock- Plug into a grounded 3-prongoutlet.- Do not move the ground plug.- Do not use an adapter.- Do not use an extension

The appliance must be connected to anelectrical outlet that is properlygrounded. The electrical installationmust comply with the applicableelectrical

71 !

M.-Nr. 10 102 130 / 07en - US, CAKWT 1603 ViKWT 1613 Vi

a Circulation fans / Active charcoal filterb Wooden racksc Insulation panel to separate the upper and middle temperature zonesd Bottle display racke C

Control panela Access buttonb Upper temperature zonec Middle temperature zoned Lower temperature zonee Temperature display:Allows you to set the tempe

Before using for the first time^ Clean the inside of the appliance andthe accessories with a mild solutionof warm water and liquid dish soap.Dry with