Operating instructionsVacuum cleanersS 560 / S 570S 700 / S 800 seriesThese operating instructions apply to standardmodels S 560 - S 578, S 711 - S 74
Connecting the suction tubesections(depending on model)Both sections of the suction tube havelocating arrows marked on them. Whenconnecting the two se
Attaching the floorhead^Push the suction tube into thefloorhead and turn it clockwise oranti-clockwise until it clicks into posi-tion.^To release the
Accessories suppliedOther tools, in addition to the floor-head(s), are supplied with the vacuumcleaner to help deal with various typesof cleaning.a Cr
To open the accessories com-partment^Press the release button and the lidwill open.^ Take out the accessory you require.^ Press down firmly on the lid
The different tools can either be fitted tothe hand-piece or, as required, to thesuction tube.FloorheadAlso for cleaning stairs.Crevice nozzleFor clea
Dusting brushFor cleaning skirting boards, ornate orcarved articles, etc. The head of thedusting brush can be swivelled to attainthe best cleaning pos
Unwinding and rewinding themains cableUnwinding^Hold the plug and unwind cable tothe required length:–S 560 - S 578: max. approx. 6.5 m–S 711 - S 748:
Switching on and off^Press the On-Off switch.Vacuuming^When vacuuming pull the cleaner be-hind you on its wheels. You can standit upright for vacuumin
Regulating the suctionThe suction power can be regulated tosuit the type of flooring. The higher thewattage the more powerful the suction.Reducing the
Rotary selector^Turn the rotary selector manually tothe suction power setting you require.Slide selector^Move the slide selector manually tothe suctio
Caring for the environmentDescription of the applianceWarning and Safety instructionsPreparing for useUsing the accessoriesFloorhead. . . . . . . . .
+ / - controlsPress the controls to select the suctionpower you require.^Press the+ control to select a highersetting.^Press the- control to select a
Automatic settingIf the Automatic setting is chosen thevacuum cleaner automatically adjuststhe suction power to suit the surfacebeing cleaned. This en
Blowing out(depending on model)The adapter is used to attach the suc-tion hose connector to the blower con-nection socket so that the vacuumcleaner ca
Park systemA Park system has been designed forconveniently parking the vacuumcleaner during pauses.^Fit the lower clip on the floorhead intothe slot o
,Always disconnect the vacuumcleaner from the electrical supply formaintenance work and for cleaning.Switch off at the wall socket and re-move the plu
When to change the dustbagChange the dustbag when the colourmarker in the dustbag change indicatorfills the display.Dustbags are designed for singleus
Replacing the dustbag^Press the release button for the dustcompartment lid and raise the lid asfar as it will go.^ To remove the dustbag hold the bagb
When to change the exhaustfilterDepending on model your vacuumcleaner will be fitted as standard withone of the following exhaust filters:a a SUPER ai
Exhaust filter change indicatorSome models are equipped with an ex-haust filter change indicator (Re-setbutton 7) which is designed for thechange cycl
Replacing the "SUPER airclean" filter^Open the dust compartment lid.^Release the filter grille and raise itupwards. Grasp the used SUPER air
Disposal of packing materialThe transport and protective packingmaterial has been selected from materi-als which are environmentally friendlyfor dispo
Replacing the "ACTIVE airclean" filter and the "ACTIVEHEPA" filter^Open the dust compartment lid.^Release the catch and remove the
Replacing one type of filterwith anotherDepending on model your vacuumcleaner will be fitted as standard withone of the following exhaust filters:a SU
When to change the dustcompartment filter (motorprotection)Replace the dust compartment filter ev-ery time you start a new packet ofdustbags.A dust co
When to change the threadliftersThe thread lifters on the suction inlet tothe floorhead and upholstery nozzlecan be replaced.Check them from time to t
,Always disconnect the vacuumcleaner from the electricity supplyfor maintenance work and for clean-ing. Switch off at the wall socket andremove the pl
The vacuum cleaner has switched it-self off automatically.A temperature limiter switches thevacuum cleaner off automatically if itgets too hot. Some m
In the event of a fault that you cannoteasily remedy, please contact–your Miele Dealeror–the nearest Miele Service Depart-ment. (See address on back p
Electrobrush(depending on model)Models designed to take an Electro-brush have a release button on thecover cap to the connection socket. Ifthere is no
Floor brush(supplied as standard with some mod-els)Special brush for cleaning hard floors(parquet, stone, PVC), and flooringwhich might be scratched,
Mattress nozzle(supplied as standard with some mod-els)For cleaning upholstery, mattresses,cushions, curtains, covers etc.Crevice nozzle (300 mm)For c
Some models are supplied with a Miele Electrobrush or Turbobrush as standard(not illustrated). These brushes are supplied with their own operating ins
MicroSetThis set is specially designed for clean-ing small objects and difficult to reachareas (such as PC keyboards, stereoequipment, intricately car
ACTIVE air clean filter(supplied as standard with some mod-els)The ACTIVE air clean filter is a specialactive charcoal filter which absorbsodours from
All electrical work should be carried outby a suitably qualified and competentperson in strict accordance with na-tional and local safety regulations.
43
Alteration rights reserved / (560/570/700/800) - 1403This paper consists of cellulose which has been bleached without the use of chlorine.M.-Nr. 05 77
a Hand pieceb Air inlet valvec Locking buttond Telescopic tube *e Slide control *f Socket for Electrobrush * (only on models with a push button on the
This appliance meets statutorysafety requirements. Inappropriateuse can however lead to personalinjury and damage to property.Read the operating instr
Do not vacuum up liquids or dampdirt. This will cause major faultsand could seriously impair the function-ing and electrical safety of the appli-ance.
Using accessoriesThe socket on the vacuum cleaner(depending on model) must onlybe used for the Miele Electrobrushspecified for use with this appliance
Attaching the suction hose^Insert the hose connector into thesuction socket until it clicks into posi-tion.To remove the suction hosefrom the cleaner^
Comments to this Manuals