Miele TOUCHTRONIC G 894 SC Technical Information

TECHNICAL INFORMATION G 600 and G 800 Dishwashers (All US Models) © 2011 Miele USA

Technical Information 10 G 600/G 800 Table 6-27: G 681, G 881 Novo Stella, G 886 Novo Stella Plus Programming Functions ... 99 Table 6-28: G 681

Technical Information 100 G 600/G 800 6. If the dishwasher door is opened and closed or the dishwasher is turned off and on, the service mode wi

Technical Information 101 G 600/G 800 6.8.5.3.1 Accessing Fault Codes 1. Access Service Mode 2. 2. Turn the program selector switch to the 1 o’

Technical Information 102 G 600/G 800 Programming Flow Chart (Electronic EGPL 02) Enter Programming Mode To access: Program index Water hardnes

Technical Information 103 G 600/G 800 Note: The program steps can be followed with a timing chart. The activation of electrical components can be

Technical Information 104 G 600/G 800 Display Fault registered F00 No fault registered F01 NTC sensor or connections open-circuited F02 N

Technical Information 105 G 600/G 800 5. After selecting options, press the Start/Stop button twice and turn the dishwasher off. Program button

Technical Information 106 G 600/G 800 6.8.7.2.1 Test Program The test program is a program that allows the technician to check all of the major f

Technical Information 107 G 600/G 800 Fault code Fault F00 No error F01 NTC or NTC connections open-circuited F02 NTC or NTC connections shor

Technical Information 108 G 600/G 800 Programming Flow Chart Enter Service Mode 2 To access: Error messages Operating hours Flow meter pulses Inc

Technical Information 109 G 600/G 800 6.8.8.2 Service Mode 1 1. To access Service Mode 1, close the door and turn the dishwasher on. All program

Technical Information 11 G 600/G 800 Table 6-79: G 818, G 658, G 858 Fault Codes ...

Technical Information 110 G 600/G 800 Program button Function Options Display Normal 130 Fault codes - F00, F01, etc. Sani Wash Operatin

Technical Information 111 G 600/G 800 Example: Sani Wash: 007 Normal 150: 127 Total operating hours: 7.127 hours 6.8.9 G 892, G 832 Program

Technical Information 112 G 600/G 800 4. The program light will either flash or stay lit, depending on the selection made (see Table 6-46 below)

Technical Information 113 G 600/G 800 6.8.9.2.1 Test Program The test program is a program that allows the technician to check all of the major fu

Technical Information 114 G 600/G 800 Fault code Program light and status Rinse light status Fault F08 Normal Plus Lit Flashing Water intak

Technical Information 115 G 600/G 800 Program Function Options Program light status Rinse & Hold Extended drying1 Off Flashing On Lit Pots

Technical Information 116 G 600/G 800 6.8.10.1.1 Setting the Water Hardness 1. Measure the water hardness in grains per gallon (gpg). 2. Access

Technical Information 117 G 600/G 800 Stage Stage function Illuminated light Stage 1 Fault codes Rinse Stage 2 Program index Drying Sta

Technical Information 118 G 600/G 800 2. Press and hold the Delay Start and Start/Stop button while turning the dishwasher on. Flashing Intake/D

Technical Information 119 G 600/G 800 6.8.11.1 Programming Mode 1. To access the programming mode, close the door and turn the dishwasher on. Th

Technical Information 12 G 600/G 800 1.0 Construction and Design 1.1 Appliance Overview 1.1.1 Typical Integrated Model Figure 1-1:

Technical Information 120 G 600/G 800 5. If the dishwasher door is opened and closed or the dishwasher is turned off and on, the service mode wi

Technical Information 121 G 600/G 800 6.8.11.3.2 Stage 2 1. To access Stage 2 of Service Mode 2, close the door and turn the dishwasher on. The

Technical Information 122 G 600/G 800 6.8.12 G 898 Programming Flow Chart Enter Programming Mode To access: Water hardness settings Extende

Technical Information 123 G 600/G 800 6.8.12.1.1 Setting the Water Hardness 1. Measure the water hardness in grains per gallon (gpg). 2. Access

Technical Information 124 G 600/G 800 1. To access Service Mode 2, close the door and turn the dishwasher on. All program lights should light. If

Technical Information 125 G 600/G 800 6.8.12.3.2 Deleting Stored Fault Codes Access Programming Mode and press Start/Stop twice. 6.8.12.3.3 Oper

Technical Information 126 G 600/G 800 Program button Function Options Button light status 1 Heated drying On2 Off Off On 2 Water hardn

Technical Information 127 G 600/G 800 6.8.13.2 Service Mode 1 1. To access Service Mode 1, close the door and turn the dishwasher on. All progra

Technical Information 128 G 600/G 800 6.8.13.3 Service Mode 2 Service Mode 2 is used to determine which upper electronic is in the appliance, to

Technical Information 129 G 600/G 800 Program button 6 Program button light Fault code and description Pressed 2 F06 Too few pulses at flow m

Technical Information 13 G 600/G 800 1.1.2 Typical Fully Integrated Model Figure 1-2: Overview of Typical Fully Integrated Model 1 Upper spr

Technical Information 130 G 600/G 800 Table 6-74: G 818, G 658, G 858 Programming Flow Chart 6.8.14.1 Programming Mode 1. To access the Program

Technical Information 131 G 600/G 800 program button 6. The program button that lights along with program button 6 will indicate the water hardnes

Technical Information 132 G 600/G 800 4. Pressing program button 6 repeatedly will allow the technician to advance through the test program. If

Technical Information 133 G 600/G 800 Program button 6 Program button light Fault code and description Pressed 1 F05 Water drainage failure,

Technical Information 134 G 600/G 800 Programming Flow Chart Enter Service Mode 2 To access: Fault codes Program index Increased water temperatur

Technical Information 135 G 600/G 800 Program button Function Options Button light status 1 Heated drying On2 Off Off On 2 Water hardness sett

Technical Information 136 G 600/G 800 2. Press and hold program buttons 1 and 2 while turning the dishwasher on. A flashing On/Off light indicat

Technical Information 137 G 600/G 800 functions include increasing the water temperature, turning on or off the water softener, adding an interim

Technical Information 138 G 600/G 800 2. Press the flashing program button 5. 3. Press the flashing program button 2. 4. The lit program butto

Technical Information 14 G 600/G 800 Figure 1-3: Novotronic Control Panel (G 841 Shown) 1.2.2 Touchtronic This series of Miele dishwashers i

Technical Information 15 G 600/G 800 Figure 1-6: Pre-Finished Dishwasher 1.3.2 Integrated This type of dishwasher is shipped with a separate

Technical Information 16 G 600/G 800 Figure 1-8: Fully Integrated Dishwasher 1.4 Technical Data 1.4.1 Dishwasher Width – Full-Size/Sliml

Technical Information 17 G 600/G 800 1.4.3 Summary of Dimensions Full-Size G 600 Series G 800 Series Height 32 ¼“ to 34 ⅞“ 33 ⅛” to 3

Technical Information 18 G 600/G 800 1.4.6 Plumbing Connections 1.4.6.1 Intake Connection The appliance is supplied with a 5-foot-long Dou

Technical Information 19 G 600/G 800 1.6 Layout of Components 1.6.1 Novotronic and Touchtronic Series Figure 1-13: Component Overview – N

Technical Information 2 G 600/G 800 Table of Contents 1.0  Construction and Design ...

Technical Information 20 G 600/G 800 1.6.2 Incognito Series Figure 1-14: Component Overview – Incognito (Vi) Series 1 Temperature sensor, R30

Technical Information 21 G 600/G 800 2.0 Installation Refer to the appliance installation manual.

Technical Information 22 G 600/G 800 3.0 Commissioning and Operation 3.1 Door Handle and Door Lock (Novotronic/Touchtronic Series) Press

Technical Information 23 G 600/G 800 3.4 Water Softener If your tap water hardness is above 8 grains per gallon (140 ppm), the water should be

Technical Information 24 G 600/G 800 4. Select a wash program by turning the program selector to the left or right. 5. Press the "Start&

Technical Information 25 G 600/G 800 4.2.1 PTC Release Element (Machines Equipped w/Turbothermic Fan) When 120VAC is applied to the release e

Technical Information 26 G 600/G 800 dispenser chamber and allow rinse aid to be dispensed into the cabinet. Note: The rinse aid only flows fro

Technical Information 27 G 600/G 800 mounted in the sump. Heater element switching is performed by the electronic via a relay. The relay (when en

Technical Information 28 G 600/G 800 Voltage 120VAC Output power 1.5kW Rated load 9.6kΩ Table 4-3: Flow-Through Heater Electrical Data 4

Technical Information 29 G 600/G 800  1 minute heater element off. The number of pulse cycles is limited to a maximum of 11. If the program’s s

Technical Information 3 G 600/G 800 4.8  Static Drying ...

Technical Information 30 G 600/G 800 Figure 4-5: Filter Assembly 4.11 Water Intake – Technical Data Solenoid valve electrical connection

Technical Information 31 G 600/G 800 The valves are physically and electrically mounted in series to ensure that if one valve should fail (e.g., d

Technical Information 32 G 600/G 800 Figure 4-7: WaterProof System Circuit - Normal Operating Position Figure 4-8: WPS Circuit - Water in Dri

Technical Information 33 G 600/G 800 4.13 Flow Meter – Operation The incoming water turns an impeller that contains a magnet located in the flow

Technical Information 34 G 600/G 800 Figure 4-10: Water Intake System with Integrated Flow Meter Figure 4-11: Water Hardness Selector With corr

Technical Information 35 G 600/G 800 4.15.2 Integrated Flow Meter Figure 4-12: Water Path with Integrated Flow Meter The water intake hose f

Technical Information 36 G 600/G 800 Figure 4-13: Water Inlet Mixer 4.15.3 Operating Solenoid Valve (Y5) (Plus Models Only) With no voltag

Technical Information 37 G 600/G 800 Figure 4-14: Water Hardness Mixer Solenoid 4.16 Electronically Controlled Water Hardness (EGS) To avoi

Technical Information 38 G 600/G 800 Figure 4-15: Water Softener Incoming water flows through the intake assembly and into the ion exchanger. Wh

Technical Information 39 G 600/G 800 Water hardness Number of program sequences before reactivation (Universal 65°C) Parts per million Grains per

Technical Information 4 G 600/G 800 5.25  WaterProof System (WPS) Restrictor Replacement ... 605.

Technical Information 40 G 600/G 800 Figure 4-16: Condenser Drying System Components If no voltage is applied to control valve Y6, the path betw

Technical Information 41 G 600/G 800 During dishwashing, the circulation pump (M6) takes in the wash water from the side of the sump through the m

Technical Information 42 G 600/G 800 Figure 4-18: Heater Pressure Switch – Contact Positions and Current Paths 4.21 Level Switch (Intake O

Technical Information 43 G 600/G 800 Figure 4-19: Water Intake/Level Switch Circuit 4.22 Temperature Sensor Temperature sensor R30 (NTC resis

Technical Information 44 G 600/G 800 Temperature Sensor R30 Resistance Values Temperature (°F (°C)) Resistance (kΩ) Tolerance (Ω) = ±5% 104

Technical Information 45 G 600/G 800 4.24 Turbidity Sensor (ECO Sensor) Certain models of dishwashers are equipped with a turbidity (ECO) sens

Technical Information 46 G 600/G 800 Component Part Activation Circulation pump M6 Relay Drain pump M8 Relay Heater relay 1K/1 soleno

Technical Information 47 G 600/G 800 5.0 Service and Maintenance 5.1 Locking Plate Adjustment 1. Loosen the two screws (Figure 5-1, Item 1

Technical Information 48 G 600/G 800 Figure 5-2: Seal Install Guide 5.3 Side Panel Removal 1. Uninstall the appliance. 2. Remove the rai

Technical Information 49 G 600/G 800 5.4 Spring Bracket Replacement 1. Remove the side panels; refer to Section 5.3. 2. Fold up the mineral w

Technical Information 5 G 600/G 800 6.8  Programming and Service Modes ...

Technical Information 50 G 600/G 800 Figure 5-5: Cover Plate Note: When reinstalling the side panels, install the bottom lip of the panel into

Technical Information 51 G 600/G 800 Warning! The basket guide must not be levered off in the area of the bolts (see Figure 5-7). This could resu

Technical Information 52 G 600/G 800 Figure 5-9: Basket Guide Stopper 7. Remove the rear stopper in the direction of the arrow (Figure 5-10, It

Technical Information 53 G 600/G 800 hose. 7. Check for proper operation. Figure 5-11: Combination Dispenser Removal 5.9 Turbothermic Fan R

Technical Information 54 G 600/G 800 Outer door panel: 1. Remove the GDU or custom panel. 2. Open the appliance door. 3. While support

Technical Information 55 G 600/G 800 5.12 Lock/Handle Assembly Removal Caution! Ensure that power is disconnected at the wall outlet by shutt

Technical Information 56 G 600/G 800 Figure 5-16: Hinge Removal 5.14 Door Tension Adjustment 1. Open the door. 2. Locate the spring adjus

Technical Information 57 G 600/G 800 2. Press the top spray arm upwards to engage it. 3. Unscrew clockwise. 5.16 Middle Spray Arm Removal

Technical Information 58 G 600/G 800 5.20 Middle Spray Arm Feed Pipe Removal 1. Remove the spray arm cover. See Section 5.19. 2. Remove th

Technical Information 59 G 600/G 800 5.22 Temperature Limiter Replacement 1. Remove the left side panel. See Section 5.3. 2. Disconnect the t

Technical Information 6 G 600/G 800 6.8.6.3 Service Mode 2 ... 1036

Technical Information 60 G 600/G 800 Figure 5-21: Pressing and Locking the Filter Assembly Note: Use caution to ensure that the filter is not d

Technical Information 61 G 600/G 800 5. Remove the restrictor with needlenose pliers; see Figure 5-23. Figure 5-23: Removing the Flow Restricto

Technical Information 62 G 600/G 800 5.27 Water Softener Operational Check Note: Ensure that the electronic is programmed “with water soften

Technical Information 63 G 600/G 800 5.29 Drip Pan Removal 1. Lay the dishwasher on its back. 2. Remove four (4) screws from the corners of t

Technical Information 64 G 600/G 800 Figure 5-26: Steam Condenser Components 5.33 Control Valve (Y6) Removal 1. Lay the dishwasher on its b

Technical Information 65 G 600/G 800 5. Disconnect the connection plug (Figure 5-27, Item 7). 6. Remove the heater pressure switch. See Section

Technical Information 66 G 600/G 800 Figure 5-28: Circulation Pump Components 5.37 Circulation Pump Housing Replacement 1. Remove the circu

Technical Information 67 G 600/G 800 Figure 5-30: Engaging the Prongs in the Circulation Pump Impeller 5. Carefully turn the releasing tool back

Technical Information 68 G 600/G 800 Figure 5-32: Heater Pressure Switch and Circulation Pump Note: When re-installing the heater pressure swit

Technical Information 69 G 600/G 800 Warning! It is essential to note correct position of the valve before removal. (The direction of flow is mar

Technical Information 7 G 600/G 800 6.8.12.2 Service Mode 1 ... 1236

Technical Information 70 G 600/G 800 3. Lay the dishwasher on its back. 4. Remove the drip pan. See Section 5.29. 5. Remove the circulation

Technical Information 71 G 600/G 800 5.45 Turbidity Sensor Removal 1. Remove as much water as possible from the sump. 2. Lay the dishwasher

Technical Information 72 G 600/G 800 3. Lift the fascia and control panel from the appliance. Figure 5-39: Control Panel (Novotronic and Touc

Technical Information 73 G 600/G 800 Figure 5-40: Removing the Mounting Bracket 5.49 Heater Relay and Power Relay Removal Note: Make note o

Technical Information 74 G 600/G 800 6.0 Fault Diagnosis 6.1 General Information Every electronically controlled Miele dishwasher has thr

Technical Information 75 G 600/G 800 6.2.7 With or Without Water Softener Used to enable or disable the water softener system.  “With water

Technical Information 76 G 600/G 800 6.4 Timing Charts – General Information A. Timer steps run along the left and right side

Technical Information 77 G 600/G 800 Note: Refer to

Technical Information 78 G 600/G 800 D. Timer step explained:

Technical Information 79 G 600/G 800 6.5 Wiring Diagrams – General Information 1 Electronic assembly (circuit boards) 2 Molex plug conne

Technical Information 8 G 600/G 800 Figure 3-1: Door Handle and Door Lock (Novotronic/Touchtronic) ... 22 Fig

Technical Information 80 G 600/G 800 6.6 Timing Charts and Wiring Diagrams (Model-Specific) Refer to the timing chart and wiring diagram guide

Technical Information 81 G 600/G 800  Rinse aid not being dispensed/released. Ensure that dispenser is operating. Note: Rinse aid should only

Technical Information 82 G 600/G 800 6.8 Programming and Service Modes Novotronic Models 6.8.1 G 841, G 841 Plus, G 842 Programming Flow

Technical Information 83 G 600/G 800 Selector switch position (o’clock) Function Options Status of Start light1 to 8 Water hardness (see Sect

Technical Information 84 G 600/G 800 Note: The program chart in the wiring diagram should be used to follow the machine functions when stepping t

Technical Information 85 G 600/G 800 6.8.1.3.1 Accessing Fault Codes 1. Access Service Mode 2. 2. Turn the program selector switch to the 1 o’cl

Technical Information 86 G 600/G 800 6.8.2 G 848 Programming Flow Chart Enter Programming Mode To access: Water hardness settings Extended d

Technical Information 87 G 600/G 800 6.8.2.1.1 Setting the Water Hardness 1. Measure the water hardness in grains per gallon (gpg). 2. Access Pr

Technical Information 88 G 600/G 800 6.8.2.3 Service Mode 2 Service Mode 2 is used to determine which upper electronic is in the machine, to ch

Technical Information 89 G 600/G 800 Selector switch position Fault code Fault 5 o’clock F04 Heating failure - heating circuit opened or defe

Technical Information 9 G 600/G 800 Figure 5-29: Sliding the Circulation Pump Tool into the Circulation Pump Intake Opening ... 66 Figure 5-30: En

Technical Information 90 G 600/G 800 Programming Flow Chart Enter Service Mode 2 To access: Fault codes Program index Increased water temperatur

Technical Information 91 G 600/G 800 Water hardness in gpg Selector switch position (o’clock) 18-21 6 22-35 7 36-70 8 Table 6-15: G 811, G 851,

Technical Information 92 G 600/G 800 3. Press and hold the Top solo button while turning the dishwasher on. Release the Top solo button and imme

Technical Information 93 G 600/G 800 6.8.3.3.2 Deleting Stored Fault Codes Access Programming Mode and turn the dishwasher off. 6.8.3.3.3 Prog

Technical Information 94 G 600/G 800 2. Press and hold the Top solo button while switching the appliance on at the on/off switch. Release the To

Technical Information 95 G 600/G 800 Appliance width [cm] Water hardness Program selector switch position (o’clock) Water hardness selector in c

Technical Information 96 G 600/G 800 6.8.4.2.1 Starting the Test Program, Program Start with Reactivation 1. Enter Service Mode 1. 2. Turn the

Technical Information 97 G 600/G 800 Program selector switch position (o’clock) Fault registered Fault indication 1 F0 No fault registered

Technical Information 98 G 600/G 800 A program can only be restarted after the fault has been addressed and the fault code has been deleted. The

Technical Information 99 G 600/G 800 mode. The display will show a program index number of P00 or P01, depending on the software version. 3. Turn