Miele PW 6201 Service Manual

Descriptive TechnicalDocumentation- Model-dependent -DTD no. 512-6161Model(s): PW 6161, PW 620124.03.2005, DE_en This information should not be duplic

PW 6161Heating Electric Gas6)High-pressuresteam(indirect)High-pressuresteam(direct)Low-pressuresteam(direct)3N AC 380 - 415 V50 - 60 Hz[mm2] 5 x 4.03

PW 6161Heating Electric Gas6)High-pressuresteam(indirect)High-pressuresteam(direct)Low-pressuresteam(direct)G-forceWash 0.67Pre-spinSpin 500Residual m

Technical data – PW 6201 (20 kg machine), version June 2004xPW 6201Heating Electric Gas6)High-pressuresteam(indirect)High-pressuresteam(direct)Low-pre

PW 6201Heating Electric Gas6)High-pressuresteam(indirect)High-pressuresteam(direct)Low-pressuresteam(direct)3 AC 440 V50 - 60 Hz[mm2] 5 x 6.0Water sup

PW 6201Heating Electric Gas6)High-pressuresteam(indirect)High-pressuresteam(direct)Low-pressuresteam(direct)Flow pressure requirementMin. [kPa] 100Max

Consumption data – PW 6161 (16 kg machine), version June 2004xPW 6161Heating Electric Gas3)High-pressuresteam(indirect)1)High-pressuresteam(direct)Low

PW 6161Heating Electric Gas3)High-pressuresteam(indirect)1)High-pressuresteam(direct)Low-pressuresteam(direct)60°C programmewith cool down -Duration[m

Consumption data – PW 6201 (20 kg machine), version June 2004xPW 6201Heating Electric Gas3)High-pressuresteam(indirect)1)High-pressuresteam(direct)Low

PW 6201Heating Electric Gas3)High-pressuresteam(indirect)1)High-pressuresteam(direct)Low-pressuresteam(direct)60°C programmewith cool down -Duration[m

D Layout of Electrical ComponentsLayout for EL version (with electric heating)xLayout 1A1 Selection-display module (BAE) EW 230A2 Door lockB1/1 Level

This information should not be duplicated or passed on without Miele approval. All rights reserved. 24.03.2005, DE_en

G1 Tachogenerator1K1/1 Relay/Contactor - Heating2K1/1 Relay/Contactor - HeatingK1/9 Relay/Contactor - DriveM2/1 Motor - FanM5 Motor - Drive1N1L Contro

GAS models, additional componentsxLayout 21B1/13 Level switch - Pump pressure2B1/13 Level switch - Pump pressureB2/13 Temperature regulator - ExhaustC

D models (with steam heating), additional componentsxLayout 3Y25 Valve - Heating (steam)Descriptive Technical DocumentationD-4 DTD no. 512-6161This in

090 Door4 Service4.1 Door cap removal / fittingA Remove the front panel, see Front panel removal, 150 4.7.A Remove the 9 fixing screws.A Remove the do

Descriptive Technical Documentation090-2 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights res

100 Fascia panel1 Technical DataxControl component Abbreviation Electronic moduleSelection-display module BAE EW 230Control-power module SLT ELP 230Mu

2 Function2.1 Profitronic M washingxFig. 1: Profitronic M control1 Multifunction buttons 1 to 62 Display (64 lines x 220 columns)3 Start button4 Multi

The Profitronic M unit controls and regulates processes in commercial washer-extractors. It can save up to a maximum of 199 programmes in 999 programm

Main components of control unit:– Selection-display module (BAE) EW 230, to operate the control unit, displaymessages, indicate control state, enable

2.2 Wash programme headerStructure and arrangement of programme header: The programme headerdescribes the general structure of a wash programme and de

ContentsGeneral InformationA Warning and Safety InstructionsB Modification HistoryC Technical DataD Layout of Electrical ComponentsFunction Groups090

Itemnumberin tableItem description Options Details11 Weigh No It is not possible to enter a weight before the start ofthe programme. The control opera

Itemnumberin tableItem description Options Details14 Fill type Water height in mm Fixes which type of monitoring is used by thecontrol to register the

Itemnumberin tableItem description Options Details17 Peak load Yes / No Peak-load cut-out: High load peaks in electricalsystems can result in particul

Model, programme and maximum load tablexModel PW 6101 PW 6131 PW 6161 PW 6201Drum volume 100 l 130 l 160 l 200 lCottons 90°C 10.0 kg 13.0 kg 16.0 kg 2

Block programming – Profitronic M washing controlxNo. Programme step Basic setting Setting options Notes0 Block name 20 blank spaces All availablealph

No. Programme step Basic setting Setting options Notes16 Wash time 1 No17 Thermostop Lock symbol18 Level 2 0 mm19 Intake path 2 Automatic20 Dispensing

2.4 Minimum heating levelThe machine has a protection system to prevent damage due to dry heating(heater elements not under water). If the programmer

2.6 Service mode (service level) – General informationThe service mode can be accessed in two different ways: Either manually directlyat the machine v

There are 2 service programme sub-divisions:xService mode (service level)1 Service programme1 Test manually2 Test automaticallyTable 10: Service progr

2.7 Data security in control-power module and selection-displaymoduleAfter a break in the mains supply, the control can register if saved data (settin

2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130-22.1 Water paths, flow rates, combination for pro

2.8 Valve summary - Series PW 6000Inlet valve summary - PW 6101, PW 6131, PW 6161, PW 6201xDesignationon switchingplanDescription Detergent dispenserc

3 Fault Repair3.1 Fault code summaryCauseSee fault code table.Fault indications in operating levelxMachine area Indication NotesGeneralPressure sensor

Machine area Indication Notes“Warning” symbol HEATINGSYSTEM FAULT! Switch off themain switch. Call the ServiceDepartment.Control registers that both h

4 Service4.1 Programming modeInitial requirementsA A wash programme must not be in operation.A The machine must not be in the service mode.AccessingA

Itemnumberin tableItem description Options Details4 ID No. (Identificationnumber)All numbers The supervisor/programmer only can read this field.The co

Itemnumberin tableItem description Options Details14 Fill type Water height in mm Fixes which type of monitoring is used by thecontrol to register the

Itemnumberin tableItem description Options Details17 Peak load Yes / No Peak-load cut-out: High load peaks in electricalsystems can result in particul

Block structurexNo. Programme step Basic setting Setting options Notes0 Block name 20 blank spaces All availablealphanumeric andspecial charactersFor

No. Programme step Basic setting Setting options Notes9 Level 1 Load/Liquor ratio: 1:0.0 kg/l10 Intake path 1 Automatic11 Dispensing type No12 Dispens

Save and quitA The appropriate settings can be saved via the save button (disk symbol).A To quit the programming mode, switch off the machine or step

A Warning and Safety Instructions1 General informationThese machines should not be installed or operated in any area where thereis a risk of explosion

Acknowledgement indicatorSuccessful accessing of the service mode is indicated by rapid flashing (5 Hz) ofthe W Start button illuminated switch surrou

xNoteAll service programmes are limited to an overriding safety time of 30 min.System analyse has the following sub-divisions:xService mode (service l

Control-power module has the following sub-divisions:xService mode (service level)1 Service programme1 Test manually2 Control-power module (component)

Selection-display module has the following sub-divisions:xService mode (service level)1 Service programme1 Test manually3 Selection-display module (co

When the desired item has been selected via the multifunction selector (jogshuttleswitch), press the OK button. The selected service programme then st

Operating data module has the following sub-divisions (control checks operatingdata module and memory card):xService mode (service level)1 Service pro

MPG (German medical product law) module has no function or test points.xService mode (service level)1 Service programme1 Test manually12 MPG moduleDes

xService mode (service level)1 Service programme2 Test automatically1 System analyseSelection-display module (EW 230)Control-power module (ELP 230)All

Operating data has the following sub-divisions:xService mode (service level)2 Service information1 Operating data1 Machine type2 ID Number SLT (contro

When the desired item has been selected via the multifunction selector (jogshuttleswitch), press the OK button. The selected service programme then st

Descriptive Technical DocumentationA-2 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights reser

Machine history has the following sub-divisions:xService mode (service level)2 Service information4 Machine history1 Total number of faults2 Water dra

Basic settings has the following sub-divisions:xService mode (service level)3 Service settings1 Basic settings1 Water drain2 Water inlet3 Heating4 Gas

4.3 Selection-display module (BAE) removal / fittingA Remove the machine lid, see Lid removal / fitting, 150 4.4.A Loosen 1 retaining screw/nut (viewe

4.5 Fascia panel removal / fittingA Remove the machine lid, see Lid removal / fitting, 150 4.4.A Remove the selection-display module, see Selection-di

Descriptive Technical Documentation100-40 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights re

130 Water intake1 Technical DataFlow pressure and flow rates.xPermitted flow pressure [bar] 1 to 10 1 to 10Valve type 3/4”, triple 3/4”, tripleFlow ra

2 Function2.1 Water paths, flow rates, combination for programmingxFig. 1: Water path summaryDescriptive Technical Documentation130-2 DTD no. 512-6161

1 2Y9, hot water 2, WAW2, compartment 2, powder detergent2 2Y6, cold water 2, KAW2, compartment 2, powder detergent3 1Y9, hot water 1, WAW1, compartme

xFig. 2: Mixer box water intake for liquid dispensing1 Control opening, water intake non-return device2 Connection KAW 4, cold water, from Y133 Connec

xFig. 3: Valves in valve blocks on machine rear panelThe flow quantities for the valve blocks are limited due to the interaction when twoor more valve

B Modification HistoryWhen? Who? What?29.11.2004 Norbert Polenz Initial compilationDescriptive Technical DocumentationDTD no. 512-6161 B-124.03.2005,

2.2 ValvesInlet valve summary - PW 6101, PW 6131, PW 6161, PW 6201xDesignationon wiringdiagramDescription Detergent dispensercompartmentSymbol Designa

2.3 Protective functions - Level monitoringThe control monitors the maximum water level in all operating states. Theprogrammer can only program the fo

Descriptive Technical Documentation130-8 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights res

150 Casing1 Technical DataxMaterial - Front panel Stainless steel 1.4016Material - Lid, side panels Galvanised sheet steel, powder coated, blueMateria

4 Service4.1 Transport informationA The machine should only be transported without a pallet if the front and rearpanel have been removed, see Front pa

xFig. 2: Rear transpor t strutsA Remove 3 screws from each rear red transport strut.A Remove the transport struts.A Take care to retain the transport

xFig. 3: Front transport strutsA Fit the front transport struts and secure each one with 3 screws.xFig. 4: Rear transpor t strutsA Fit the rear transp

4.4 Lid removal / fittingA Remove 1 screw from each side of the lid at the top of the machine.A Lift the lid slightly at the front and disconnect its

4.7 Front panel removalA Remove 1 screw on each side of the front panel from the underneath of thebottom edge.A Pull the bottom edge outwards slightly

160 Documents1 Technical DataWiring diagram, wiring diagram legend, switching plan, multifunction module,operating instructions, programming instructi

Descriptive Technical DocumentationB-2 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights reser

Descriptive Technical Documentation160-2 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights res

500 Testing, special documents1 Technical DataLog book for testing in accordance with accident prevention legislation.Descriptive Technical Documentat

Descriptive Technical Documentation500-2 DTD no. 512-6161This information should not be duplicated or passed on without Miele approval. All rights res

C Technical DataTechnical data – PW 6161, version June 2004xPW 6161Heating Electric Gas6)High-pressuresteam(indirect)High-pressuresteam(direct)Low-pre