Miele DA 371 User Manual

Installation instructionsGas hobsKM370G/KM370-1 GKM 371 GKM390G/KM391GTo avoid the risk of accidents ordamage to the appliance, it isessential to read

KM 390a Building-in depthb Mains connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)Appliance dimensions and worktop cut-out10

KM 391a Building-in depthb Mains connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)Appliance dimensions and worktop cut-out11

^Prepare the worktop cut-out asshown in the diagram.Remember to maintain a minimumsafety distance of 50 mm betweenthe hob and the back wall and150 mm

Building in the appliance^Feed the electricity connection cablethrough the cut-out and connect.^Place the gas hob in the preparedcut-out.^Make the gas

Do not let sealant get in between thehob frame and the worktop.This could cause difficulties if thehob ever needs to be taken out forservicing and pos

All electrical work should be carriedout by a suitably qualified andcompetent person, in strictaccordance with current local andnational safety regula

ImportantThe electrical safety of this appliancecan only be guaranteed whencontinuity is complete between it andan effective earthing system, whichcom

Connection to the gas supply, orconversion from one type of gas toanother should only be undertakenby an approved and registered gasinstaller in stric

a Connection with test pointspecifically for GBb Connection with test pointspecifically for GB and 90° angleNatural gas / liquid gas^The appliance is

Nominal rating for all gas types with the burner full onBurner Gas type KM 370 G / KM 370-1 G /KM 371 GKM 390 G / KM 391 GkW g/h kW g/hSmallburnerNatu

G This appliance can be used in countries other than those specified on theappliance. It is, however, set up for connection to the gas and electricity

KM 370 G / KM 370-1 G /KM 371 GWhen converting to anothe type ofgas, the main jets and the small jetson all burners have to be changed.Screw in the ne

Changing the jetsDisconnect the gas hob from theelectricity supply by switching off atthe socket and withdrawing the plugor by removing the mains fuse

Wok burner^Take off the burner cap a, burnerring b and burner head c.^Loosen screws d and remove thecover plate.^Using an M7 socket spannerunscrew the

Changing the small jets(for all burners)To change the small jets, the burnersecuring screws must first be loosenedand the upper section of the applian

After changing the jets^Assemble the removed burner partsin reverse order and check for leaksby operating the burner without theupper section of the h

KM 390 G / KM 391 GWhen converting to another type ofgas, the main jets and the small jetson all burner have to be changed.Screw in the new jets accor

Changing the jetsDisconnect the gas hob from theelectricity supply by switching off atthe socket and withdrawing the plugor by removing the mains fuse

Wok burner^Take off the burner cap a, burnerring b and the burner head c.^Loosen screws d and remove thecover plate.^Using an M7 socket spannerunscrew

Changing the small jetsTo change the small jets, the burnersecuring screws must first be loosenedand the upper section of the applianceremoved.^Remove

Wok burnerb Small jet with smaller diameter(e.g. for liquid gas: 0.20).c Small jet with larger diameter(e.g. for liquid gas: 0.46).^Remove the ignitor

Gas-heated appliancesSafety precautions to take if you smell gasß Turn off the gas emergency control valve immediately.This is usually located near th

After changing the jets^Assemble the removed burner partsin reverse order and check for leaksby operating the burner without theupper section of the h

31

Alteration rights reserved / 3209M.-Nr. 05 827 720 / 10

Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Appliance dimensions and worktop

Building inFit wall units and extractor hoodbefore fitting the hob, to avoiddamaging the appliance.~The veneer or laminate coating ofworktops (or adja

~The room in which the gas hob isinstalled must be at least 20 m3in sizewith a door or window in it which canbe opened to the outside air.~Using the g

KM 370a Building-in depthb Mains connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)Appliance dimensions and worktop cut-out7

KM 370-1 Ga Building-in depthb Mains connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)Appliance dimensions and worktop cut-out8

KM 371a Building-in depthb Mains connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)Appliance dimensions and worktop cut-out9