Miele PW 6241 Operations Instructions

Operating and Installation InstructionsWasherPW 6241PW 6321To prevent accidentsand appliance damageread these instructionsbeforeinstalling or use.M.-N

1. Turn on the washer^Open the on-site water faucet (and the supply fau-cet for steam, if relevant).^Turn on the electrical supply at the mains (on si

To prevent fabric damage, check that laundry willnot be caught in the closed door.^ Close the drum door with the handle.Do not swing the door shut.Max

DetergentOnly use the correct amount of high efficiency lowsudsing detergent. Too much detergent will causeoversudsing.DosageFollow the instructions o

StarchIn the detergent container1 Hot WashmProgram stop - Starch stopDoor can be opened.i ü f"Program stop - Starch Stop" flashes in the dis

4. Select a program^Select a program by turning the jog shuttle (e.g.Program 1 Hot Wash).The following will appear in the display:18 Extra Drain1 Hot

6. Adjust the program (if needed)Laundry weightThe laundry weight can be manually selected.1 Hot Wash 54.0 /54.0 lb104 °F Pre-wash194 °F Main wash e+i

7. Select Delay Start (if needed)Use the m "Delay start" button to program the washerto start automatically at a later time.Setting the dela

9. End of programAt the end of the program, once the drum isstationary and no water is in the machine the displayshows (for example):1 Hot WashProgram

Skipping program cyclesCycles of a program in progress can be skipped orrepeated.^Press the f "End" button to stop the program.1 Hot WashPro

Canceling a program^To cancel a program, press the f "End" button twi-ce.If the program was canceled with water in themachine or during spin

2

Program sequenceThe program sequence is shown in the display afterthe start of the program.1 Hot Wash104 °F Pre-wash 68 °FMain wash End at 12:35+im k

Language selectionThe language can be selected with the F flagsymbol. The language is set back to its originalsetting 5 minutes after the program ends

Chip cards are programmed to a machine type.Empty cards can be used with any machine.^Press l "On" to turn the washer on.The Welcome screen

Liquid dispensing system(Dispensing systems vary)Priming the dispensing pumpsa Hose connection socket (in)b Leakage outletc Hose connection socket (ou

Priming the dispensing pumpsUse the calibration to get liquid detergent to thepumphead. Once calibration is complete run anempty program to get deterg

Peak load cutoffWhen activating the peak load cutoff the heat isturned off and the program is stopped. The displayshows:1 Hot WashProgram stop - Peak

After each useNever use high pressure cleaners to hose downthe machine.The machine should be cleaned immediately afteruse.^ After use do not shut the

Vent grille^Check and clean regularly the wash water vent gril-le at the rear of the machine.RustThe drum and the wash water drum are made ofstainless

Drum bearing lubricationIf the machine needs to be serviced the followingmessage shows:§Drum bearing lubricationCall Technical Service.A^ Press A &quo

Reasons for oversudsingDetergent type^Only use detergent formulated for use in commerci-al washers. Detergents for domestic machines arenot suitable.T

IMPORTANT SAFETY INSTRUCTIONSGuide to the washerOperating panel ...8Use1. Tu

Power failure - Emergency door releaseDuring a short power failureThe program remains in the last position. Whenpower is restored the following messag

Display Maintenance notice^Call Technical Service for maintenance if the dis-play shows the following message after turning themachine on.§Maintenance

MWater intake faultCall Technical Serviceif restart w/o success.if^Check the water supply and press "Start"./Door lock faultContact Technica

^In the event of a fault which you cannot correctyourself, please contact Technical Service.^When contacting Technical Service please quotethe model,

1 Model2 Serial number3 Item number4 Material number5 Voltage / Frequency6 Control breaker7 Motor8 Drum data9 Drum diameter / Drum depth10 Spin speed1

Installation Instructions

Disposal of the packing materialsThe packing materials protect the appliance duringshipping. They have been designed to bebiodegradable and recyclable

The washer must only be installed by a Mieleauthorized service technician.Before installation or service disconnect the powersupply to the work area.T

PlumbingThe machine should be connected to two watersupply faucets, which conform with local and nationalregulations. Installation must be carried out

Electrical connection,All electrical work must be performed by aqualified service technician in accordance withapplicable codes and standards.When ins

Explanation of safety instructions andwarnings on the washerRead the operating instructions.Read all the instructions, e.g. theinstallation instructio

1.Sort the laundryOnly use this machine for items that are machine washable, see the fabric care label.^Empty all pockets.2.Turn the machine on and lo

41

42

43

Alteration rights reserved / 3112INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCTSPECIFICATIONS, TECHN

Electrical Safety~Be certain this appliance is properly installed andgrounded by an authorized technician. For electrical safetythis machine must be g

Additional information~Disinfecting and cleaning agents often contain chlorides(salts) which can cause steel surfaces to rust. To protectthe machine f

a Emergency Stop buttonPressing the red button turns the machine off.b Control panelc Detergent compartmentsPull the handle to open the flap.d Drum do

Operating panela Display*1 Hot Wash 194 °F2 Cottons 140 °F3 Cottons Intensive 140 °Fi FC AAfter turning the machine on, the display showsbriefly a wel

Control keys^Press once to activate the function, press again todeactivate the function.i Manual operation(Used by Miele Service Technicians)See Progr