Miele G 8066 Operations Instructions

Operating instructionsCommercial dishwasherG 8066To avoid the risk of accidents ordamage to the machine it isessential to read these instructionsbefor

Personnel operating the machineshould be trained regularly.Untrained personnel should not beallowed access to the machine or itscontrols.This machine

The following points should beobserved to assist in maintainingquality standards, to protect users,and to avoid damage to the machineand items being c

In countries where there are areaswhich may be subject to infestationby cockroaches and other vermin, payparticular attention to keeping themachine in

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly fordisposal, and

Before using the machine for the firsttime, the following steps must becarrried out.Each step is described in moredetail in the appropriate sectionfur

To open the door^Grasp the handle and open the door.The door should only be opened duringoperation for emergencies, e.g. ifarticles are knocking toget

Only applies to machines with abuilt-in water softener.To achieve good cleaning results, thedishwasher needs to operate with softwater. Hard water res

Table of settingsmmol/l or°dmmol/l °f Valuedisplayed12345678910111213141516171819202122232425262728293031323334350.20.40.50.70.91.11.31.41.61.82.02.22

Filling the salt reservoirOnly use special coarse grainedreactivation saltwith granules ofapprox. 1-4 mm. Do not use other saltssuch as cooking salt,

Rinsing out salt residues at the endof operation^Press the Z button.^Press and hold the 6 button andpress Y at the same time.The rinsing process will

Description of the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Guide to the machine. . . . . . . . . .

Rinsing agent is necessary to ensurewater does not cling and leave markson items during the drying phase andto help items dry faster after they havebe

Please remember to fill the containerin good time, it should not beallowed to empty completely.Adding rinsing agent and venting thedispensing systemSe

^Grasp the service panel handle andopen the panel.^ Take the red cap off the filler spout.^ Using the funnel supplied fill thecontainer with rinsing

Preparing the loadRemove coarse residues and empty allcontainers before loading into themachine.,Do not use metal scourers orwire wool to remove resid

Items not suitable fordishwashers:–Cutlery with wooden or horn handles.–Wooden or plastic cutting boards.–Heat sensitive plastic items (see"Progr

Loading examplesThe dishwasher can be supplied with astandard range of baskets, or withbaskets to suit your individualrequirements. The diversity of i

,Only use cleaning agentsformulated for use in this type ofmachine. Do not use cleaningagents designed for domesticdishwashers.Some types of soiling m

Adding liquid cleaning agent:The dishwasher can also be connectedto an optional DOS Module G 60 fordispensing liquid cleaning agent.See "Programm

G 8066 WES DOS andG 8066 DOS:These versions of the dishwasher arefitted, as standard, with a built-in liquiddispensing pump and reservoir forcleaning

Preparing the machine^Close the door.^Open the stopcock.^Press the Y button to switch thedishwasher on.All the programme button indicatorlights will l

Programming special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321. Setting the DOS 1 cleaning agent dosage c

Selecting a programmeChoose your programme according tothe type of load and the degree ofsoiling.The different programmes and theiruses are described

Changing a programmeProvided the Start button has not yetbeen pressed, a wrongly selectedprogramme may be changed asdescribed below (if it has beenpre

For future servicing work, pleasedocument any alterations to the stan-dard factory settings.Enter any alterations in the relevantValue set:box.Alterin

1.1 Setting the cleaning agentdispensing methodTo set the dispensing method, first callup Programming level 2 as follows:^Switch off the machine with

1.2 Setting the cleaning agentdosage concentration levelIf the dispensing method has beenprogrammed for liquid cleaning agent,you can alter the dispen

2. Setting the DOS 2 rinsingagent dosage concentrationlevel and venting thedispensing system(Programming level 3)2.1 Selecting the rinsing agentdispen

2.3 Venting the dispensing system^Call up Programming level 3(see 2.1).Then, or if you were already inProgramming level 3, vent thedispensing system a

3. Setting the main wash orfinal rinse temperature and / orfinal rinse duration(Programming level 4)Please make a note of any changesto the main wash

3.2 Setting the offset range for thefinal rinse temperature^Call up Programming level 4(see 3.1).Then, or if you were already inProgramming level 4, s

4. Buzzer (Programminglevel 5)Programming level 5 allows you toactivate a buzzer to sound when–a programme has finished = areminder tone–a fault has o

Problem solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Cleaning the drain pump and non-

5. Altering the programmeduration (Programming level 6)You can set the programme duration ina range from 75 seconds to 480seconds.Lengthening the prog

5.2 Altering the programme durationfor the STANDARD programme^Call up Programming level 6(see 5.1).Then, or if you were already inProgramming level 6,

6. Resetting the factory defaultsettingsYou can reset all parameters back tothe factory default settings inProgramming level 7. To do this youmust fir

Cleaning the wash cabinet,tank and filters,The dishwasher must not beused without all the filters in place.The tank and the filter combinationshould b

Cleaning the flat filters,The water in the tank can be hot.The tank must be drained beforeremoving the filters.^ First remove the flat filter at the f

E-Cloth^A microfibre "E-Cloth" is availablefrom the Miele UK Spare PartsDepartment, which is suitable forcleaning surfaces such as stainless

With the aid of the following guide, minor problems can be easily correctedwithout calling in a Miele service technician, saving you both time and mon

Problem Possible cause RemedyThe wash cycle finishesearly and the 6indicator light flashes(fault code F..A appearsin the display).Before rectifying th

Problem Possible cause RemedyThe dishes are notclean.The dishes were notloaded correctly. Disheswere placed inside otherpieces, water could notaccess

Problem Possible cause RemedyWhite residue is visibleon cutlery and crockery,clouding occurs onglassware; film can bewiped off.Not enough rinsing agen

This Miele machine is a commercialdishwasher with a tank system, shortbatch times and large cleaningcapacity for washing crockery andcutlery in restau

Other fault codesIf a fault code which is not referred to inthe previous pages, appears in thedisplay, proceed as follows:^Switch off the machine with

Cleaning the drain pump andnon-return valveIf water has not been pumped away atthe end of a programme the drainpump or the non-return valve might bebl

Cleaning the filters in the waterinletFilters are incorporated in the screwconnection of the water inlet hose toprotect the water inlet valve. If thes

Should you still have any difficulties or ifa fault code "F..." appears in the displayagain, please contact:–your authorised Miele Service D

Please refer to the installationdiagram supplied with the machine.,Furniture and fittings installednear the machine must be of acommercial standard ab

,All electrical work must becarried out by a suitably qualifiedand competent person inaccordance with local and nationalsafety regulations.–Connection

Connection to the water inlet,Water in the machine must notbe used as drinking water.–The machine must be connected tothe water supply in accordance w

Drainage–The drainage system is fitted with anon-return valve which prevents dirtywater from flowing back into themachine via the drain hose.–The mach

Programme1)When to use Powder cleaning agent2)Follow manufacturer'sinstructionsAINTENSIVE3 minFor heavily soiled crockery with driedon soiling.40

Programme sequenceMain wash3) 4)Run-off Final rinse3) 5)65°C/160 sec 5 sec 85°C/15 sec65°C/100 sec 5 sec 85°C/15 sec65°C/70 sec 5 sec 85°C/15 sec2 mi

Control panela On buttonb Off buttonc DRAIN programme buttond SHORT programme buttone STANDARD programme buttonf INTENSIVE programme buttong Start but

Height: 82 (85) cmWidth: 60 cmDepth: 60 cmVoltage: see data plateConnected load: see data plateFuse rating: see data plateMains connection cable: appr

61

62

63

M.-Nr. 06 743 480 / 00en-GBAlteration rights reserved/4205

Overviewa Connection for DOS Module(Dispensing system for liquidcleaning agent) on the rear righthand side, only applies to machineswithout a built-in

G 8066 DOS and G 8066 WES DOS:a Service panelb Cleaning agent level indicatorc Handle for opening the service paneld Rinsing agent level indicatorGuid

This machine complies with allrelevant local and national safetyrequirements. Incorrect use can leadto personal injury and damage toproperty.To avoid